Skip to product information
1 of 5

PayPal, credit cards. Download editable-PDF and invoice in 1 second!

GB/T 39089-2020 English PDF (GBT39089-2020)

GB/T 39089-2020 English PDF (GBT39089-2020)

Regular price $170.00 USD
Regular price Sale price $170.00 USD
Sale Sold out
Shipping calculated at checkout.
Quotation: In 1-minute, 24-hr self-service. Click here GB/T 39089-2020 to get it for Purchase Approval, Bank TT...

GB/T 39089-2020: Bamboo toothpicks

This standard specifies the product types, technical requirements, inspection methods, inspection rules, identification, packaging, transportation, storage of bamboo toothpicks. This standard applies to bamboo toothpicks, which are used for tooth picking, using bamboo, yellow bamboo, single bamboo and other bamboo materials as raw materials. This standard does not apply to coated bamboo toothpicks.
GB/T 39089-2020
NATIONAL STANDARD OF THE
PEOPLE REPUBLIC OF CHINA
ICS 79.020
Y 87
Bamboo toothpicks
?????????
ISSUED ON: SEPTEMBER 29, 2020
IMPLEMENTED ON: APRIL 01, 2021
Issued by: State Administration for Market Regulation;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions... 4
4 Product types ... 6
5 Technical requirements ... 7
6 Inspection methods ... 8
7 Inspection rules ... 9
8 Marking, packaging, storage, transportation ... 10
Bamboo toothpicks
1 Scope
This standard specifies the product types, technical requirements, inspection methods, inspection rules, identification, packaging, transportation, storage of bamboo toothpicks.
This standard applies to bamboo toothpicks, which are used for tooth picking, using bamboo, yellow bamboo, single bamboo and other bamboo materials as raw materials. This standard does not apply to coated bamboo toothpicks.
2 Normative references
The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard.
GB/T 191 Packaging - Pictorial marking for handling of goods
GB/T 1931 Method for determination of the moisture content of wood
GB/T 2828.1-2012 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
3 Terms and definitions
The following terms and definitions apply to this document.
3.1
Bamboo toothpicks
Bamboo sticks, which are used for picking teeth, using bamboo, yellow bamboo, single bamboo and other bamboo materials as raw materials.
3.2
Little tip
The slender tip of the toothpick's tip.
3.3
Barbed tip
The barb-shaped tip of the toothpick tip.
3.4
Split tip
Stubble at the tip of a toothpick.
3.5
Arris tip
Longitudinal prismatic tip on the tip of the toothpick.
3.6
Decay
Due to the invasion of decay fungus, the cell wall material is decomposed, which leads to the loosening of the bamboo tissue structure, the decrease of strength and density, the change of bamboo tissue color.
3.7
Split
Separation of bamboo fibers, along the bamboo grain direction.
3.8
Wane
Cylinder edge defects, which are caused by planing, sanding, bumping, or undersized bamboo toothpick material.
3.9
Stain
Local discoloration or stains on the surface, which is caused by the influence of microorganisms, metals or chemicals.
3.10
Length (L) inspection is measured by a steel ruler, which is accurate to 0.5 mm. 6.2.3 Diameter
The diameter of the cylinder (d1) is inspected, at one-half of the full length. The plane diameter of the tip (d2) is inspected, at the smallest point at the tip, by a vernier caliper, which is accurate to 0.02 mm.
6.2.4 Taper angle of tip
The taper angle of tip (??) inspection shall be carried out, at the tips, by a universal angle ruler.
6.3 Determination of moisture content
Take samples with complete packaging; make determination according to the provisions of GB/T 1931.
7 Inspection rules
7.1 Inspection classification
Product inspection is divided into exit-factory inspection and type inspection. 7.2 Exit-factory inspection
Each batch of products shall be subject to exit-factory inspection. The exit-factory inspection includes the following items:
- Sensory inspection;
- Specification size and deviation inspection;
- Inspection of moisture content.
7.3 Type inspection
7.3.1 Inspect all items.
7.3.2 After one year of normal production, type inspection shall be carried out, in one of the following situations:
- Trial-type identification of new products or products after trans-plant production; - During formal production, where there are major changes in structure, raw materials, processes;
- When the production is restored after suspension for more than half a year;

View full details