1
/
von
6
PayPal, credit cards. Download editable-PDF and invoice in 1 second!
GB/T 41749-2022 English PDF (GBT41749-2022)
GB/T 41749-2022 English PDF (GBT41749-2022)
Normaler Preis
$230.00 USD
Normaler Preis
Verkaufspreis
$230.00 USD
Grundpreis
/
pro
Versand wird beim Checkout berechnet
Verfügbarkeit für Abholungen konnte nicht geladen werden
Delivery: 3 seconds. Download true-PDF + Invoice.
Get QUOTATION in 1-minute: Click GB/T 41749-2022
Historical versions: GB/T 41749-2022
Preview True-PDF (Reload/Scroll if blank)
GB/T 41749-2022: General requirements for surface condition of hot-rolled sections
GB/T 41749-2022
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.140.70
CCS H 44
General requirements for surface condition of hot-rolled
sections
(ISO 20723:2004, Structural steels - Surface condition of hot-rolled sections -
Delivery requirements, MOD)
ISSUED ON: OCTOBER 12, 2022
IMPLEMENTED ON: OCTOBER 12, 2022
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Classification ... 5
5 Measurement rules ... 5
6 Grinding requirements ... 8
7 Repair welding and its inspection rules ... 10
8 Numerical rounding off ... 12
Annex A (informative) Comparison on structure number between this document and
ISO 20723:2004 ... 13
Annex B (informative) Technical differences between this document and ISO
20723:2004 and their reasons ... 15
Foreword
This document was drafted in accordance with the rules given in GB/T 1.1-2020
"Directives for standardization - Part 1: Rules for the structure and drafting of
standardizing documents".
The revision of the document adopts ISO 20723:2004 "Structural steels - Surface
condition of hot-rolled sections - Delivery requirements".
Compared with ISO 20723:2004, there are many structural adjustments in this
document. See Annex A for a list of structural numbering comparisons between the two
documents.
Compared with ISO 20723:2004, this document has many technical differences. A
single vertical line (|) is used to mark the outer margin of the terms involved. See Annex
B for a list of these technical differences and their causes.
The following editorial changes are made to this document:
- Delete Annex A of ISO 20723:2004.
Attention is drawn to the possibility that some elements of this document may be the
subject of patent rights. The issuing authority shall not be held responsible for
identifying any or all such patent rights.
This document was proposed by China Iron and Steel Association.
This document shall be under the jurisdiction of National Technical Committee on Steel
of Standardization Administration of China (SAC/TC 183).
The drafting organizations of this document: Maanshan Iron and Steel Co., Ltd., Laiwu
Branch of Shandong Iron and Steel Co., Ltd., Hebei Jinxi Iron and Steel Group Co.,
Ltd., Rizhao Iron and Steel Holding Group Co., Ltd., Anshan Zizhu Technology Steel
Co., Ltd., Hebei Tianzhu Iron and Steel Group Co., Ltd., Zhongzhong Technology
(Tianjin) Co., Ltd., Metallurgical Industry Information Standard Research Institute.
Main drafters of this document: Wu Baoqiao, Wu Meizhuang, Wang Zhongxue, Xu
Mingwang, Wei Zhenzhou, Wu Jiajun, Li Xiuqing, Ma Bingbing, Liu Baoshi, Zhang
Wenman, Zhang Pei, Wang Yujie, Ma Yongfu, Wang Fuliang, Gao Fengguo, Wu Lihong,
Gao Kun, Li Yu, Zhao Xinhua, Xing Jun, Xia Meng.
General requirements for surface condition of hot-rolled
sections
1 Scope
This document specifies the surface condition classification, measurement rules,
grinding requirements, repair welding and its inspection rules, numerical rounding off
for hot-rolled sections.
This document applies to the surface condition of hot-rolled H-beam and split T-beam,
hot-rolled equilateral angle steel, hot-rolled unequal angle steel, hot-rolled L-beam, hot-
rolled I-beam, hot-rolled channel steel sections (hereinafter referred to as section), of
which the nominal thickness is 3mm ~ 160mm. The surface includes all surfaces except
the rolled edge.
2 Normative references
The following referenced documents are indispensable for the application of this
document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
YB/T 081, Rule for rounding off of numerical values and judgement of testing values
for technical standards of metallurgy
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 imperfections
Except for cracks, scabs, folds, delamination and cracks, surface discontinuities whose
depth and (or) area are not greater than the specified limit value.
3.2 defects
Cracks, scabs, folds, delamination and splits, as well as surface discontinuities with
depth and/or area greater than specified thresholds.
3.3 area of check
The area where the defect (under) is located.
processing, and the defect is caused by the manufacturer, the manufacturer is allowed
to re-delivery after grinding or welding according to the requirements of this document.
5.1.4 If this document is quoted in the contract or in the product standard, but the surface
condition category and level of the product are not specified, it shall be regarded as
Category A Level 1.
5.2 Determination of depth and affected area of surface discontinuities
5.2.1 Depth determination
Depths of representative surface discontinuities shall be determined, if necessary, in
order to distinguish surface discontinuities from imperfections and defects. The
measurement shall be carried out from the surface of the product. Depth is measured
after grinding to remove representative surface discontinuities.
5.2.2 Determination of affected area
If necessary, the affected area of the surface discontinuity shall be determined according
to the following provisions.
a) For isolated surface discontinuities, draw a continuous line along the perimeter of
the surface discontinuity at a distance of 20mm from it. Then draw a rectangle 20mm
from the edge of the discontinuous defect to determine the affected area, as shown
in Figure 1. If the surface discontinuity is less than 20mm from the rolling edge of
the section, the rolling edge of the section shall prevail.
b) For aggregated surface discontinuities, draw a continuous line along the periphery
of the group of surface discontinuities at a distance of 20mm from it. Then draw a
rectangle 20mm away from the discontinuous line of this group of surfaces. If the
surface discontinuity of this group is less than 20mm from the rolling edge of the
section, the rolling edge of the section shall prevail, as shown in Figure 2.
c) For striped surface discontinuities, draw a rectangle. The distance between the
four sides of the rectangle is 20mm from the edge of the discontinuous defect. If this
group of surface discontinuities is less than 20mm from the edge of the section, the
rolling edge of the section shall prevail, as shown in Figure 3.
d) The surface discontinuity of a strip shall be at least 10 times its greatest width.
Multiple surface discontinuities whose edges are not more than 40mm apart shall be
regarded as one aggregated surface discontinuity (including aggregated surface
discontinuities and striped surface discontinuities).
grinding wheel grinding before welding repair. The bottom of the part where the defect
is removed shall be smooth and free of sharp corners. The parts to be welded shall be
free of grease or other organic substances, water, rust and so on.
7.2.1.5 Appropriate welding rods and welding repair processes shall be used according
to the designation of steel.
7.2.1.6 Use suitable methods such as grinding wheel to grind the welding repair.
Remove the protruding metal. Make weld repairs flush and smooth with the rolled
surface. It shall not be fixed-point continuous grinding. Make the surface bluish.
Get QUOTATION in 1-minute: Click GB/T 41749-2022
Historical versions: GB/T 41749-2022
Preview True-PDF (Reload/Scroll if blank)
GB/T 41749-2022: General requirements for surface condition of hot-rolled sections
GB/T 41749-2022
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.140.70
CCS H 44
General requirements for surface condition of hot-rolled
sections
(ISO 20723:2004, Structural steels - Surface condition of hot-rolled sections -
Delivery requirements, MOD)
ISSUED ON: OCTOBER 12, 2022
IMPLEMENTED ON: OCTOBER 12, 2022
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Classification ... 5
5 Measurement rules ... 5
6 Grinding requirements ... 8
7 Repair welding and its inspection rules ... 10
8 Numerical rounding off ... 12
Annex A (informative) Comparison on structure number between this document and
ISO 20723:2004 ... 13
Annex B (informative) Technical differences between this document and ISO
20723:2004 and their reasons ... 15
Foreword
This document was drafted in accordance with the rules given in GB/T 1.1-2020
"Directives for standardization - Part 1: Rules for the structure and drafting of
standardizing documents".
The revision of the document adopts ISO 20723:2004 "Structural steels - Surface
condition of hot-rolled sections - Delivery requirements".
Compared with ISO 20723:2004, there are many structural adjustments in this
document. See Annex A for a list of structural numbering comparisons between the two
documents.
Compared with ISO 20723:2004, this document has many technical differences. A
single vertical line (|) is used to mark the outer margin of the terms involved. See Annex
B for a list of these technical differences and their causes.
The following editorial changes are made to this document:
- Delete Annex A of ISO 20723:2004.
Attention is drawn to the possibility that some elements of this document may be the
subject of patent rights. The issuing authority shall not be held responsible for
identifying any or all such patent rights.
This document was proposed by China Iron and Steel Association.
This document shall be under the jurisdiction of National Technical Committee on Steel
of Standardization Administration of China (SAC/TC 183).
The drafting organizations of this document: Maanshan Iron and Steel Co., Ltd., Laiwu
Branch of Shandong Iron and Steel Co., Ltd., Hebei Jinxi Iron and Steel Group Co.,
Ltd., Rizhao Iron and Steel Holding Group Co., Ltd., Anshan Zizhu Technology Steel
Co., Ltd., Hebei Tianzhu Iron and Steel Group Co., Ltd., Zhongzhong Technology
(Tianjin) Co., Ltd., Metallurgical Industry Information Standard Research Institute.
Main drafters of this document: Wu Baoqiao, Wu Meizhuang, Wang Zhongxue, Xu
Mingwang, Wei Zhenzhou, Wu Jiajun, Li Xiuqing, Ma Bingbing, Liu Baoshi, Zhang
Wenman, Zhang Pei, Wang Yujie, Ma Yongfu, Wang Fuliang, Gao Fengguo, Wu Lihong,
Gao Kun, Li Yu, Zhao Xinhua, Xing Jun, Xia Meng.
General requirements for surface condition of hot-rolled
sections
1 Scope
This document specifies the surface condition classification, measurement rules,
grinding requirements, repair welding and its inspection rules, numerical rounding off
for hot-rolled sections.
This document applies to the surface condition of hot-rolled H-beam and split T-beam,
hot-rolled equilateral angle steel, hot-rolled unequal angle steel, hot-rolled L-beam, hot-
rolled I-beam, hot-rolled channel steel sections (hereinafter referred to as section), of
which the nominal thickness is 3mm ~ 160mm. The surface includes all surfaces except
the rolled edge.
2 Normative references
The following referenced documents are indispensable for the application of this
document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
YB/T 081, Rule for rounding off of numerical values and judgement of testing values
for technical standards of metallurgy
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 imperfections
Except for cracks, scabs, folds, delamination and cracks, surface discontinuities whose
depth and (or) area are not greater than the specified limit value.
3.2 defects
Cracks, scabs, folds, delamination and splits, as well as surface discontinuities with
depth and/or area greater than specified thresholds.
3.3 area of check
The area where the defect (under) is located.
processing, and the defect is caused by the manufacturer, the manufacturer is allowed
to re-delivery after grinding or welding according to the requirements of this document.
5.1.4 If this document is quoted in the contract or in the product standard, but the surface
condition category and level of the product are not specified, it shall be regarded as
Category A Level 1.
5.2 Determination of depth and affected area of surface discontinuities
5.2.1 Depth determination
Depths of representative surface discontinuities shall be determined, if necessary, in
order to distinguish surface discontinuities from imperfections and defects. The
measurement shall be carried out from the surface of the product. Depth is measured
after grinding to remove representative surface discontinuities.
5.2.2 Determination of affected area
If necessary, the affected area of the surface discontinuity shall be determined according
to the following provisions.
a) For isolated surface discontinuities, draw a continuous line along the perimeter of
the surface discontinuity at a distance of 20mm from it. Then draw a rectangle 20mm
from the edge of the discontinuous defect to determine the affected area, as shown
in Figure 1. If the surface discontinuity is less than 20mm from the rolling edge of
the section, the rolling edge of the section shall prevail.
b) For aggregated surface discontinuities, draw a continuous line along the periphery
of the group of surface discontinuities at a distance of 20mm from it. Then draw a
rectangle 20mm away from the discontinuous line of this group of surfaces. If the
surface discontinuity of this group is less than 20mm from the rolling edge of the
section, the rolling edge of the section shall prevail, as shown in Figure 2.
c) For striped surface discontinuities, draw a rectangle. The distance between the
four sides of the rectangle is 20mm from the edge of the discontinuous defect. If this
group of surface discontinuities is less than 20mm from the edge of the section, the
rolling edge of the section shall prevail, as shown in Figure 3.
d) The surface discontinuity of a strip shall be at least 10 times its greatest width.
Multiple surface discontinuities whose edges are not more than 40mm apart shall be
regarded as one aggregated surface discontinuity (including aggregated surface
discontinuities and striped surface discontinuities).
grinding wheel grinding before welding repair. The bottom of the part where the defect
is removed shall be smooth and free of sharp corners. The parts to be welded shall be
free of grease or other organic substances, water, rust and so on.
7.2.1.5 Appropriate welding rods and welding repair processes shall be used according
to the designation of steel.
7.2.1.6 Use suitable methods such as grinding wheel to grind the welding repair.
Remove the protruding metal. Make weld repairs flush and smooth with the rolled
surface. It shall not be fixed-point continuous grinding. Make the surface bluish.
Share





